Ripatuned incognito lower pulley

[G-Ride990]

Ripatuned Incognito Lower Damper Sleeve Kit (no crank pin kit)

***IN ORDER NOTES, PLEASE LEAVE YEAR MAKE AND MODEL DUE TO VARIATIONS IN ACCESSORY BELT DRIVE LENGHT*** We are proud to announce the “Incognito” crank damper sleeve system! We have taken everything into consideration with this direct bolt on crank damper sleeve to take the labor out of...

ripatuned.com

Looks pretty badass and doesn't require a tune! Claimed 775whp

 

[DiabeticSith]

Ripatuned Incognito Lower Damper Sleeve Kit (no crank pin kit)

***IN ORDER NOTES, PLEASE LEAVE YEAR MAKE AND MODEL DUE TO VARIATIONS IN ACCESSORY BELT DRIVE LENGHT*** We are proud to announce the “Incognito” crank damper sleeve system! We have taken everything into consideration with this direct bolt on crank damper sleeve to take the labor out of...

ripatuned.com

Looks pretty badass and doesn't require a tune! Claimed 775whp

That's a hell of a gain over stock. Looks interesting.

 

[G-Ride990]

That's a hell of a gain over stock. Looks interesting.

Especially if not needing a tune is true. With the limited research I have done though that seems to be true. Bolt on power!

 

[DiabeticSith]

Especially if not needing a tune is true. With the limited research I have done though that seems to be true. Bolt on power!

Mo Powa Babeh James Pumphrey GIF - Mo Powa Babeh James Pumphrey Donut Media - Discover & Share GIFs

Click to view the GIF

tenor.com

 

[Shaggy]

Especially if not needing a tune is true. With the limited research I have done though that seems to be true. Bolt on power!

With no tune at all? Really?

 

[G-Ride990]

With no tune at all? Really?

Only bumps the boost up a PSI or two. I would imagine the stock PCM could compensate for such a small difference. That is way less than the difference you would see driving at sea level vs Colorado with a blower setup like the TRX.

 

[BlackGold6.4]

check this out, wasn't sure where to post it but has to do with pulley changes

 

[Trailmaker]

Ripatuned Incognito Lower Damper Sleeve Kit (no crank pin kit)

***IN ORDER NOTES, PLEASE LEAVE YEAR MAKE AND MODEL DUE TO VARIATIONS IN ACCESSORY BELT DRIVE LENGHT*** We are proud to announce the “Incognito” crank damper sleeve system! We have taken everything into consideration with this direct bolt on crank damper sleeve to take the labor out of...

ripatuned.com

Looks pretty badass and doesn't require a tune! Claimed 775whp

I think @Bambi did this mod?!

 

[Bambi]

I think @Bambi did this mod?!

Yep. Gets you from 10.5 to 12 psi. No tune required. There are one or two people getting belt slippage.

I haven’t seen an independent dyno but has put these in the 11’s

 

[Jwil]

That's insane. Huge value for the price tbh. Even if you could get another 50 hp... easiest mod for serious hp.

 

[Bambi]

A lot of owners that want to keep their warranty are running the unpinned version. About 2 hours and returned to stock with no ecu record.

I’m getting a build together that will light my powertrain warranty on fire though lol

 

[Jwil]

A lot of owners that want to keep their warranty are running the unpinned version. About 2 hours and returned to stock with no ecu record.

I’m getting a build together that will light my powertrain warranty on fire though lol

Oh for sure!

As for your build... Any spoilers?

 

[Bambi]

Oh for sure!

As for your build... Any spoilers?

Whipple 3.0, built bottom end, stage 2 fi-interchiller, 108mm nick williams tb, bwoody intake (already on, may change if something better comes out), headers(tbd maker), pump gas/flex/110/e85 tunes with associated pulleys for the boost levels, maybe 100-200 shot of nos for giggles.

I’m not great with moderation obviously lol. Only thing holding it up is the whipple isn’t going to be out until January.

Based on the slips I’m seeing, should be a low 11/high 10 second truck which is mindblowing.

I might get a set of wheels with 33’s or smaller just for the street.

Possibly someones cat back exhaust but the factory routing/flow looks pretty good and I already cut out the mufflers.. replaced with straight tubing. It sounds glorious.

 

[Jwil]

Whipple 3.0, built bottom end, stage 2 fi-interchiller, 108mm nick williams tb, bwoody intake (already on, may change if something better comes out), headers(tbd maker), pump gas/flex/110/e85 tunes with associated pulleys for the boost levels, maybe 100-200 shot of nos for giggles.

I’m not great with moderation obviously lol. Only thing holding it up is the whipple isn’t going to be out until January.

Based on the slips I’m seeing, should be a low 11/high 10 second truck which is mindblowing.

I might get a set of wheels with 33’s or smaller just for the street.

Possibly someones cat back exhaust but the factory routing/flow looks pretty good and I already cut out the mufflers.. replaced with straight tubing. It sounds glorious.
View attachment 650

Dude that sounds incredible. Can't wait to see some progress!! Do you have a build thread?

 

[Busa Dave]

For those that are interested. Bambi has left the building....

RAM-TRX.com Legend - We Lost Bambi Yesterday

All, You don't know me, but I am Bambi's brother-in-law. Yesterday, @Bambi, the Stripper Hunter, died. Bambi spent a lot of his time here and loved his Ram TRX, as you all no doubt know. You also know that he lived an outsized life and spared no one from a good ribbing. We lost him far too...

www.ram-trx.com

 

[Nick@GotExhaust]

For those that are interested. Bambi has left the building....

RAM-TRX.com Legend - We Lost Bambi Yesterday

All, You don't know me, but I am Bambi's brother-in-law. Yesterday, @Bambi, the Stripper Hunter, died. Bambi spent a lot of his time here and loved his Ram TRX, as you all no doubt know. You also know that he lived an outsized life and spared no one from a good ribbing. We lost him far too...

www.ram-trx.com

Oh no, thats terrible news. RIP

 

[G-Ride990]

For those that are interested. Bambi has left the building....

RAM-TRX.com Legend - We Lost Bambi Yesterday

All, You don't know me, but I am Bambi's brother-in-law. Yesterday, @Bambi, the Stripper Hunter, died. Bambi spent a lot of his time here and loved his Ram TRX, as you all no doubt know. You also know that he lived an outsized life and spared no one from a good ribbing. We lost him far too...

www.ram-trx.com

So sad! I only just started talking to him the other day about 2a stuff. Seemed like a really cool guy.

 

[Shaggy]

For sure said. Seemed like a no BS guy and was getting to know him. Will be missed for sure.